Prospects of applying ferrite sheet steels in the food industry

Authors

Keywords:

Corrosion resistance ferrite steel, food industry, heat resistance

Abstract

Purpose. Evaluate the possibility of applying a sheet material of 08H8SYuTch 08Kh18T1 grades of steels and for the manufacture of heat-resistant parts of nodes for furnace fittings. Techniques. The sheet material of 08H8SYuTch 08Kh18T1 grades of steel is obtained on the basis of previously developed recommendations for modes of additional thermal strip plate treatment. Obtained parts and nodes of heat-resistant fittings were assembled on the "Minelli-100" furnace, which have been operated for two years. Results.  It was found that there is a partial precipitation of carbides and there duction of hot work hardening level based on the appropriate heat treatment conditions, while maintaining the fine grainat 6 points, which generally has a positiv eeffect on the formability during rolling process. In carryin gout aditional thermal treatment of hot-rolled strip plate there is a selection both iron chromium carbide (Cr, Fe)23C6 and more difficult soluble carbonitrides Ti(C, N) in the structure, which leads to slower migration of angleboundaries at thermal effects including welding heating. The intermediate review of existing furnaces showed that at operating temperatures of 550–850 °C there was only a change of the colour from light blue to gray on the parts but a thin, dense oxides cale appeared on the most heated places on the furn aceparts. The practical significance. The use of the proposed grade of steels for manufacturin gparts for heat-resistantfurnace fittings made it possible to increase the service life of the furnacesin 1.5–2 times.

Author Biography

V. L. Greshta, Zaporizhzhya National Technical University

The department of physical materials, Professor

References

Оборудование пищевых производств. Материаловедение: монография / [Ю. П. Солнцев, В. Л. Жавнер, С. А. Вологжанина, Р. В. Горлач]. – Санкт-Петербург : Профессия, 2003. – 526 с.

Solntsev Y.P., Zhavner V.L., Vologzhanina S.A. and Gorlach R.V. Oborudovanie pischevyh proizvodstv. Materialovedenie [Equipment for food production. Materials Science]. Saint-Petersburg : Profession Publ., 2003, 526 p. (in Russian).

Коррозионностойкие стали и сплавы : монография / [А. А. Бабаков, М. В. Приданцев]. – Москва: Металлургия, 1971. – 319 с.

Babakov A.A. and Pridantsev M.V. Korrozionnostojkie stali i splavy [Corrosion-resistant steels and alloys]. Moscow : Metallurgy Publ., 1971, 319 p. (in Russian).

Гудермон Э. Специальные стали: в 2 т. / Э. Гудермон. – Москва : Металлургия, 1959. – Т. 1. – 952 с.

E. Gudremon Special'nye stali [Special steel] Moscow : Metallurgy Publ., 1959, vol. 1, 952 p. (in Russian).

Химуши Ф. Ф. Нержавеющие стали / Ф. Ф. Химушин. – Москва : Металлургия, 1967. – 798 с.

Khimushin F. F. Nerzhaveyuschie stali [Stainless steels]. Moscow : Metallurgy Publ., 1967, 798 p. (in Russian).

Грешта В. Л. Дослідження впливу термічної обробки на структуру холоднокатаних листових феритних корозійностійких сталей / В. Л. Грешта // Вісник Приазовського державного технічного університету: технічні науки. – 2014. – Вип. 29. – С. 90–96.

Greshta V. L. Doslіdzhennya vplivu termіchnoї obrobki na strukturu holodnokatanih listovih feritnih korozіjnostіjkih stalej [The influence of heat treatment on the structure of the cold executioner sheet corrosion-resistant steels ferritic]. Vіsnik Priazovs'kogo derzhavnogo tehnіchnogo unіversitetu [Journal of Azov State Technical University : Engineering Series]. 2014, vol. 29, pр. 90–96. (in Ukrainian).

Пикеринг Ф. Б. Физическое металловедение и разработка сталей / Ф. Б. Пикеринг. – Москва : Металлургия, 1982. – 182 с.

Pikering F. B. Fizicheskoe metallovedenie i razrabotka stalej [Physical metallurgy and the design of steels]. Moscow : Metallurgy Publ., 1982. 182 p. (in Russian).

Христенко И. Н. Анализ кривых упрочнения / И. Н. Христенко // Металлы. – 1985. – № 5. – С. 139–141.

Khristenko I.N. Analiz krivyh uprochneniya [Analysis of the hardening curves]. Metally [Metals]. 1985, no. 5, pр. 139–141. (in Russian).

Бондаренко А. Л. Физическая трактовка упрочнения при штамповке ферритных нержавеющих сталей / А. Л. Бондаренко, В. С. Виниченко, Ю. Т. Рыбаченко // Новые конструкционные материалы и эффективные методы их получения и обработки. – 1988. – С. 32–36.

Bondarenko A.L., Vinichenko V.S. and Rybachenko Y.T. Fizicheskaya traktovka uprochneniya pri shtampovke ferritnyh nerzhaveyuschih stalej [Physical treatment hardening during forming of ferritic stainless steels]. Novye konstrukcionnye materialy i `effektivnye metody ih polucheniya i obrabotki. [New construction materials and effective methods for their production and processing]. 1988, pp. 32–36. (in Russian).

Грешта В. Л. Оцінка здатності до формозмінювання листових феритних корозійностійких сталей за результатами технологічних випробувань / В. Л. Грешта // Нові матеріали і технології в металургії та машинобудуванні. − 2014. – № 1. – С. 100–103.

Greshta V.L. Ocіnka zdatnostі do formozmіnyuvannya listovih feritnih korozіjnostіjkih stalej za rezul'tatami tehnologіchnih viprobuvan' [Grade ability to forming sheet ferritic steels corrosion on the results of technological tests]. Novі materіali і tehnologії v metalurgії ta mashinobuduvann [New materials technologies in metallurgy and machine building]. 2014, no. 1, pp. 100–103. (in Ukrainian).

Бондаренко А. Л. Состояние границ зерен, механические свойства и штампуемость ферритных нержавеющих сталей / А. Л. Бондаренко // МиТОМ. – Киев, 1978. – № 11. – С. 30–33.

Bondarenko A.L. Sostoyanie granic zeren, mehanicheskie svojstva i shtampuemost' ferritnyh nerzhaveyuschih stalej [Status grain boundaries, mechanical properties and formability ferritic stainless steels]. MiTOM [M&TTM]. Kyiv, 1978, no. 11, pp. 30–33. (in Russian).

Бондаренко А. Л. Перерозподіл вуглецю при нагріві і охолодженні заготівок під час виробництва із феритних корозійностійких сталей / А. Л. Бондаренко, В. Л. Грешта, Л. П. Степанова // Нові матеріали і технології в металургії та машинобудуванні. − 2000. – № 2. – С. 33–36.

Bondarenko A.L., Greshta V.L., Bondarenko A.L. and Stepanova L.P. Pererozpodіl vuglecyu pri nagrіvі і oholodzhennі zagotіvok pіd chas virobnictva іz feritnih korozіjnostіjkih stalej [Redistribution carbon at heating and cooling in the production of corrosion-resistant steelsferritic]. Novi materIali i tehnologii v metalurgii ta mashinobuduvanni [New materials technologies in metallurgy and machine building]. 2000, no. 2, pp. 33–36. (in Ukrainian).

Ольшанецький В. Ю. Деякі особливості процесів розчинення-виділення карбідних фаз у феритних нержавіючих сталях з титаном / В. Ю. Ольшанецький, А. Л. Бондаренко, В. Л. Грешта, Л. П. Степанова // Нові матеріали i технології в металургії та машинобудуванні. – 2003. – № 2. – С.7–10.

Olshanetskyy V.Yu., Bondarenko A.L., Greshta V.L. and Stepanov L.P. Deyakі osoblivostі procesіv rozchinennya-vidіlennya karbіdnih faz u feritnih nerzhavіyuchih stalyah z titanom [Some features of the process of dissolution-allocation of carbide phases in ferritic stainless steels and titanium]. Novі materіali і tehnologії v metalurgії ta mashinobuduvannі [New materials technologies in metallurgy and machine building]. 2003, no. 2, pp. 7–10. (in Ukrainian).

Долотова Т. С. Влияние режимов термической обработки на свойства стали 000Х11 Н10М2Т / Т. С. Долотова, В. И. Кучерявый, О. К. Ревакина // МиТОМ. – Киев, 1973. – № 12. – С. 9–10.

Dolotova T.S., Curly V.I. and Revakina D.C. Vliyanie rezhimov termicheskoj obrabotki na svojstva stali 000X11 N10M2T [Effect of heat treatment on the properties of steel 000X11 N10M2T]. MiTOM [M&TTM]. Kyiv, 1973, no. 12, pp. 9–10. (in Russian).

Published

2015-12-19